You are browsing documentation for a version other than the latest stable release. Switch to the latest stable release, 1.4.
When Building a Mender Yocto Project image for your own project and device, you encounter a build error similar to the following:
ERROR: Multiple .bb files are due to be built which each provide u-boot (.../tisdk/sources/meta-variscite/recipes-bsp/u-boot/u-boot-var-som-am33.bb .../tisdk/sources/meta-ti/recipes-bsp/u-boot/u-boot_2014.07.bb). This usually means one provides something the other doesn't and should.
Mender needs to configure U-Boot in order to support robust rootfs rollback. If your project relies on a fork of U-Boot this needs to be integrated. For more information, see Integrating with U-Boot, in particular the section on Forks of U-boot.
This may be an indication that Mender's automatic U-Boot patching has failed for the particular board that's being built for, and a manual patch may be required. For information on how to create such a patch, go to the Manual U-Boot integration section.
Sometimes it happens that U-Boot will refer to a storage device as
mmc 0, whereas the Linux kernel will refer to the same device as
/dev/mmcblk1 (note the different index). In this case the Mender build system must be told explicitly about this disagreement. To do so, you can set the following two variables:
MENDER_UBOOT_STORAGE_INTERFACE = "mmc" MENDER_UBOOT_STORAGE_DEVICE = "0"
which will set the index that U-Boot will use. All non-U-Boot references to the storage device, including the
root argument passed by U-Boot to the Linux kernel when booting it, will keep using the
/dev/mmcblk1 variant derived from
By default Mender does not add any bootloader files to the boot partition. If your device requires this you need to specify the files in the
IMAGE_BOOT_FILES variable in the
machine.conf file for your device. For example:
IMAGE_BOOT_FILES ?= "u-boot.bin MLO"
See the Yocto Project documentation for more information about the
In order to support robust rootfs rollback, Mender depends on being able to tell the bootloader to roll back to the known-working rootfs if attempts to boot the updated rootfs fails a given number of times. Currently, Mender uses the Boot Count Limit feature of U-Boot to achieve this. If you see errors similar to the following during the Yocto Project build process, the U-Boot you are using most likely does not support this feature.
include/config_mender.h:34:3: error: #error CONFIG_BOOTCOUNT_ENV is required for Mender to work
There are two alternatives to resolve this issue. Either you can upgrade to U-Boot v2014.07 or newer, where Boot Count Limit was introduced, or you can patch your current U-Boot version to support this or a similar feature. Please see Bootloader support for more information.
This is most likely because you are producing an image that has a lot of small files, so many that the filesystem runs out of blocks, even if there is enough space when counting bytes. There are several ways this can be remedied:
Check if you have
dbg-pkgs set in
EXTRA_IMAGE_FEATURES. This will cause debug packages to be included in the image, which typically contain a lot of small files. If you don't need the debug information, this feature can be disabled.
Increase the size of the image by increasing the value in
MENDER_STORAGE_TOTAL_SIZE_MB (see description in Variables), which will also increase the number of blocks. However, note that unless it is increased greatly, this will still give you a filesystem which is fairly close to the block limit, so the problem could happen during production instead, if the device writes enough files.
EXTRA_IMAGECMD_ext4 = " -b 1024"in
local.conf. The default is 4096, it must be a power of 2, and it must not be smaller than 1024.
The symptom is an error message similar to this:
ERROR: u-boot-fw-utils-mender-auto-provided-1.0-r0 do_package: objcopy failed with exit code 1 (cmd was 'arm-poky-linux-gnueabi-objcopy' --only-keep-debug '/home/user/poky/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/u-boot-fw-utils-mender-auto-provided/1.0-r0/package/sbin/fw_printenv' '/home/user/poky/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/u-boot-fw-utils-mender-auto-provided/1.0-r0/package/sbin/.debug/fw_printenv'): arm-poky-linux-gnueabi-objcopy:/home/user/poky/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/u-boot-fw-utils-mender-auto-provided/1.0-r0/package/sbin/fw_printenv: File format not recognized ERROR: u-boot-fw-utils-mender-auto-provided-1.0-r0 do_package: Function failed: split_and_strip_files ERROR: Logfile of failure stored in: /home/user/poky/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/u-boot-fw-utils-mender-auto-provided/1.0-r0/temp/log.do_package.15130 ERROR: Task (/home/user/poky/meta-mender/meta-mender-core/recipes-bsp/u-boot/u-boot-fw-utils-mender-auto-provided_1.0.bb:do_package) failed with exit code '1'
This is a known bug in U-Boot versions prior to v2017.05. If you get this error, the auto-provided recipe won't work, so you will have to carry out the steps in the u-boot-fw-utils guide. Note that only the section under "u-boot-fw-utils" is necessary, the other sections on the same page, such as
MENDER_UBOOT_AUTO_CONFIGURE = "0", should not be necessary to carry out unless you have other reasons to do so.